ZDDP Plus engine oil treatment. 
Four oz. bottle will treat 5 Qts of oil and keep your flat tappet cam alive.

Jet drive impeller shafts

AQ Standard shaft  AQ Cut for inducer  17-4 PH Standard 17-4 Cut for inducer

$345.00 $399.00 $375.00 $449.00

top of  page

Rebuild Kits

top of  page

Aggressor performance drive w/ manual Hydro trim 
diverter includes rudder and choice of nozzle ring.  Add $200.00

17-4 pro race impeller shaft w/oversized bearing retainer 
and replaceable, hard chromed, tail bearing sleeve     Add $100.00

Pro race w/ Mag bronze impeller    Add  $365.00

Billet S/S Inducer impeller     Add $485.00

**Sale Price plus S&H**
(California residents subject to 9.25% sales tax.)

S/S Billet Pre-Loader Impeller

top of  page

top of  page

top of  page

top of  page

Top quality used impellers reworked&matched to a new stepped wear ring.
Limited Stock (A, A/B, & B cuts)     $225.00

top of  page

Reduce pressure in your engine block for improved reliability and temperature control.
As shown   $119.00

top of  page

Improve clamping force by 50%.  Cheaper than double drilling your suction housing and bowl.
As Shown   $55.00

top of  page

SPLIT BOWLS

AGGRESSOR
Stronger new generation 9 vane bowl that is a nice piece 
and comes with bearings and seal.
Without stuffer    $595.00
With stuffer      $625.00 
When available.

American Turbine/Dominator
New generation 8 vane bowls are very nicely made and come complete with bearings and seals.  These bowls are machined on the inside of the inlet side of the bowl, behind the impeller, to accept the impeller stuffer skirt that is cast into A/T and Dominator impellers.  This system reduces turbulence behind the impeller.  Other impellers without the stuffer skirt will fit just fine.
A/T for Berkeley 10 1/4 standard     $595.00
Dominator 10 1/4 standard heavy duty bowl with larger OD.  The Transom adapter ID will have to be enlarged approximately 5/16" to fit this bowl.  If you have  set back pump (no transom adapter), this bowl is your best choice.     $595.00

BERKELEY
8 vane bowls are very nicely made and are the last to 
offer oil lubrications for the shaft tail bearings.
2010 SALE  $849.00

-----photo coming soon------

LEGEND BOWLS
This is a very nicely made 7 vane bowl that has an oil bath for the shaft tail bearings 
and a stuffer system designed into the casting.  Standard impellers will fit 
this bowl.  This bowl fits only the Legend jet drive unless you order the Legend 
bowl that is built to fit a Berkeley 10 1/4" case.
$799.00

THERMOSTAT KITS

Stainless steel bypass thermostat kits for Chevy and Olds

Harbin Marine polished bypass T stat kit   Complete   $115.00
Note-some water pump cover plates may have to be drilled out and taped for a 1/2" N.P.T. to accommodate the inlet tees.

Set of four hose fittings, 1/2"  N.P.T. x 5/8" hose    $12.00

NEW FOR 2010!
460 Ford Thermostat Kit
As most of you Ford lovers know, the bypass thermostat kits available for Chevy and Olds do not fit the 460 Ford Engines.  Jim at Performance Jet has a 460 Ford engine in his 21 foot Eliminator.  The engine temp was always running cold, so we figured a way to control the temperature without breaking the budget.  This system has been working nicely for our customers for many years, so Performance Jet decided to offer this setup as a kit.

The kit includes a new T stat housing with the divider milled out to accept a 160 degree marine thermostat that is specially drilled for this setup.  In conjunction with the thermostat and housing, the Performance Jet water pressure relief kit MUST be used and is included as part of the kit.

Note: Performance Jet recommends that both outlets on the thermostat housing be plumbed to dump overboard, and they do if you have thru Transom exhaust.  If your boat runs headers, it is recommended that you find another water source for your headers and dump both T stat outlets overboard.  

This kit is offered for $175.00 complete.

-----photo coming soon-----

DROOP SNOOTS, STRAIGHT SNOOTS, 
AND SNOOT KITS

American Turbine long droop snoot lowers your thrust line in relation to the shaft center line for increased lift on most smaller boats.  Steering pins set at 7 degree up angle.  Lowers thrust line 1 3/16"

Aggressor long droop snoots do the same.

Long droop snoots     $225.00

Place diverter long droop snoots are very nicely made and incorporate a bolt-on ride plate if you choose.  These snoots lower the thrust line two full inches, and the steering pins are set 7 degrees up.  This piece allows you to enjoy the advantages of a ride plate without having to pull your intake adapter to machine for a shoe and ride plate combo.
$325.00

The place diverter high performance housing is a nice reinforced short droop that lowers the thrust line 1/2 inch.  The steering pins are set at 3.5 degrees up angle.  Great for all boats, especially tunnel bottoms.

Place High Performance Housing     $325.00

The long straight snoot, designed by Duane at High Tech Performance is a long straight snoot that works very well on most applications.  This snoot has no bends to restrict flow.  The steering pins are set straight.  This snoot moves the thrust point farther aft without pushing the Transom downward.
$330.00

DROOP SNOOT KITS

Performance Jet is offering droop snoot kits that include all of the hardware you need plus a billet steering extension and swivel assembly.

A/T or Aggressor style snoot with Billet extension   $290.00

Place diverter long droop kit without ride plate.  
Includes all hardware and billet steering extension.   
$395.00

Add ride plate    $128.00
Place HPH short snoot with short steering extension     $395.00

HTP Straight snoot kit with steering extension.     
$399.00

Billet steering extensions with swivels, short or long     $69.00  

Due to the nature of the marine industry, prices are subject to change.